Difference between revisions of "Using Visual Studio"

From Inkscape Wiki
Jump to navigation Jump to search
m (→‎Make error: formatting)
Line 100: Line 100:
If you get the error below, it means the environment variables are not set up correctly. Do not use mingwenv.bat to set up the environment variables, but set them in the Windows System Settings instead as described here: [[Compiling Inkscape on Windows#Set_Environmental_Variables|Setting Environment Variables]]
If you get the error below, it means the environment variables are not set up correctly. Do not use mingwenv.bat to set up the environment variables, but set them in the Windows System Settings instead as described here: [[Compiling Inkscape on Windows#Set_Environmental_Variables|Setting Environment Variables]]


Error:
   --- i18n / msgfmt
   --- i18n / msgfmt
   Make error line 422: executeCommand : could not create process : the system cannot find the file specified.
   Make error line 422: executeCommand : could not create process : the system cannot find the file specified.

Revision as of 04:27, 7 March 2015

Introduction

Microsoft Visual Studio is a popular development tool used primarily with C, C++, and C#. Visual Studio (community edition) can be downloaded for free but it requires a plugin called VisualGDB or WinGDB. These plugins are not free, but fully functional evaluation versions are available. This wiki focuses on the VisualGDB plugin, but WinGDB settings are also provided.

This page will help you set up Visual Studio for coding, building, and stepping through code in Inkcape.

Installation

  1. Follow all steps of guide Compiling Inkscape on Windows.
  2. Make sure Inkcape compiles correctly using the console first.
  3. Install Visual Studio.
  4. Install VisualGDB.
  5. Set the Environment variables in the Windows System settings as described here: Compiling Inkscape on Windows. Do not use mingwenv.bat to set the environment variables.

Note: It is assumed the required packages are installed in the following directories:

  • c:\mingw
  • c:\devlibs
  • c:\src\inkscape\trunk

Create project in Visual Studio

  1. Open Visual Studio.
  2. Select File->New->Project->Installed->Templates->VisualGDB->MinGW/Cygwin Project Wizard.
  3. For the project location, do not use a path with spaces.

    New-project.png

  4. Give the project a name, and click OK.
  5. At the wizard, select Project Type->Import a project build with command-line tools.

    Import-project.png

  6. Click Next.
  7. Check the path to MinGW is correct.
  8. Click Next.
  9. Set the Inkscape source directory to:
    • c:\src\inkscape\trunk
    • Note: Do not set this directory to \src
  10. Select Import preserving directory structure.

    Import-project-settings.png

  11. Click Next.
  12. At Build Command, select Customize.
  13. Set Arguments to:
    • /c "c:\src\inkscape\trunk\btool.exe"
  14. Select OK.
  15. At Clean Command, select Customize.
  16. Set Arguments to:
    • /c "c:\src\inkscape\trunk\btool.exe" clean
  17. Select OK.
  18. At Debug Settings->Executable file to debug, browse to:
    • C:\src\inkscape\trunk\inkscape\inkscape.exe

      Build-settings.png

    • Note: The field "Working directory relative to the build directory" is automatically set to "inkscape". This is correct.
  19. Click Finish and wait for the project generation to finish.

Note: VisualGDB will not copy the source files to the Visual Studio project directory, so you can still use Version Control the usual way.
Note: The project settings can be changed at a later time by going to: Project->VisualGDB Project Properties.

Enable debugging

In Explorer, open build.xml located in:

  • c:\src\inkscape\trunk

Then look for the "T A R G E T : C O M P I L E" section, go to the <flags> section, and change

 -O2

to

 -O0

Also add this flag:

 -g


Flags.png

Then search for this:

 strip="true" symfile="${build}/inkscape.dbg"

And change to this:

 strip="false" symfile="${build}/inkscape.dbg"


Strip.png

Note: these changes will make Inkscape very slow to compile.

Building Inkscape

  1. In Visual Studio, select Build->Clean Solution.
  2. Then select Build->Build Solution.
  3. Compiling will take even longer then a release version of Inkscape.

Note: The compiler will seem to be stuck at this for a while, but that is normal:

 1>  --- compile / cc

Stepping through code

  1. In Visual Studio, go to Solution Explorer->Inkscape->Source Files->src->main.cpp, and set a breakpoint here:

    Breakpoint.png

  2. Select Debug->Start Debugging With GDB.
  3. If you get a "GDB command timeout" window, be patient.
  4. Inkscape will stop at the breakpoint. Happy debugging.

Trouble shooting

Unable to break

In case Visual Studio cannot break at a certain breakpoint (most likely no debugging symbols present), you can diagnose breakpoint problems using the VisualGDB diagnose tool:


Diagnose-breakpoint.png

Make error

If you get the error below, it means the environment variables are not set up correctly. Do not use mingwenv.bat to set up the environment variables, but set them in the Windows System Settings instead as described here: Setting Environment Variables

 --- i18n / msgfmt
 Make error line 422: executeCommand : could not create process : the system cannot find the file specified.
 Make error line 422: <msgfmt> problem:

Build failed

If you get the error below, the main build directory is incorrect. Delete the project and make a new project using the wizard, paying attention to the correct paths.

 Error 1	error : Command-line action failed
 Error 2	error : Build has failed. See the Output window for more details.
 Error 3	error MSB3073: The command ""C:\VisualGDB\\VisualGDB.exe" /build exited with code 1.

Clean failed

If Clean fails with error code -1, make sure you close inkscape first.

WinGDB settings

Wizard settings:

  • File->New->Project->Installed->Templates->WinGDB->WinGDB Standard Projects->Multiplatform Executable->OK
  • MinGW installation directory: C:\MinGW
  • Make executable location: C:\src\inkscape\trunk\btool.exe
  • Source dir: C:\src\inkscape\trunk\src
  • Group imported files in folders = true
  • Build result directory: C:\src\inkscape\trunk\inkscape
  • Build debuggable result: inkscape.exe
  • Build working directory: C:\src\inkscape\trunk
  • Working directory: C:\src\inkscape\trunk
  • Additional source directories: C:\devlibs

Project settings:

  • Right click project->WinGDB->Properties->:
  • Environment->Debugger path: C:\mingw\bin\gdb.exe
  • Environment->Build toolchain paths: C:\MinGW\bin;C:\src\inkscape\trunk
  • Debug->Executable path: C:\src\inkscape\trunk\inkscape\inkscape.exe
  • Directories->Additional source directories: C:\devlibs
  • Project build->Project build command: btool
  • Project build->Project rebuild command: btool clean; btool
  • Project build->Project clean command: btool clean
  • Project build->Build working directory: C:\src\inkscape\trunk

Building:

  • WinGDB->Build->Build projectname

Debugging:

  • WinGDB->Start debugging